- Peralatan Kesehatan
- Peralatan Pendidikan Teknik
- PowerBox Systems
- Cara Beli
- Tentang Kami
- Kontak Kami
- Peta Situs
- Konfirmasi Pembayaran
Simplify your next nitro powered model setup with our Linear BEC and Glow Driver 2 in 1 unit. This handy unit combines an onboard glow plug driver with a linear BEC to run your servos. Just one battery to handle the entire model. A small LED indicator board gives a series of warnings or displays what settings have been chosen, as well as the button to manually activate the onboard glow driver and doubles as your on/off switch. The onboard glow driver can also be remotely activated through your transmitter. When using it on a 3 position switch, you can select off, full power for startup, or half power which is great to make sure the plug stays lit as you come in to land and the engine is at idle. Running at half power also conserves battery and prolongs the glow plug's life.
For the Linear BEC portion, you can select between 5.9V output or 7.2V regulated output to get the most out of your high voltage servos. This regulated BEC can handle a constant current up to 5 amps, with burst current going as high as 20 amps. A low voltage warning on the LED board will alert you if the input voltage starts to get too low.
If you like clean installations and simplicity, check out our Linear BEC and Glow Driver 2-in-1. Less wires, and less batteries to charge make your life, and airplane or heli much simpler.
• Linear BEC and glow driver in 1 convenient unit
• Programmable BEC output voltage 5.9 V or 7.2 V
• Regulated BEC handles 5 amps continuous, or up to 20amps burst current
• Control the glow driver manually or by remote
• Can detect if glow plug is not working correctly
• Time out, short circuit, low voltage and overheat protection
• Low voltage alarm
Input Voltage: 7.4V (2S LiPoly)
Output Voltage: 5.9 or 7.2V
Constant Current: 5A
Burst Current: 20A (10 Sec)
Input Connector: JST
*Note: Instructions are located in the files tab below.
The all new Multistar twin output SBEC is an advanced switching DC-DC regulator designed specifically with multirotors in mind.
It will simultaneously supply a constant 5Amps at 5V and 10Amps at 12V. It works with 2-13 cell lipoly packs and supplies an interference free constant 5V to your receiver and 12v to a gimbal, camera or any other 12V accessory.
Always check the input voltage of any accessory before connecting the SBEC supply to it.
Input protection: Reverse polarity protection
Output (Constant): 5v/5A and 12v/10A
Input: 6v-50v (2-13cell lipoly)
Dimensions: 60 x 25 x 17mm
The RotorStar 6S 10A Super Mini S-BEC supplies a constant voltage to the receiver and servos in your model. ESCs that have a built-in linear BEC can easily overheat and thus lose efficiency when used in high performance applications such as 3D helicopters, this is due to the use of multiple high power digital servos which can draw a lot of current.
By using the RotorStar Super Mini BEC, you can ensure your model has the reliable and stable power that it needs.
• Compact size and lightweight
• 6V 10A output
• Wide input voltage range: 6~25.2VDC
• Dual output leads for extra security
• Over-current and over-heat protection functions
• Fully enclosed design makes the unit water resistant
• 90% or higher efficiency
Input Voltage: 6~25.2V (2S~6S lipoly)
Output Current: 10A max
Output Voltage: 6V +/-0.1V
Working Temp: -20~65°C
Storage Temp: -10~70°C
Output Plug Type: JR style
Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.
The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.
The Turnigy SK3 motors are suited to modelers who are seeking a qualitymotor without compromise.
Internal resistance: 0.045 Ohm
Max Loading: 33A
Max Power: 430W
Shaft Dia: 4.0mm
Bolt holes: 25mm
Bolt thread: M3
Motor Plug: 3.5mm Bullet Connector
vegetable replicas with a kit that offers great savings. Includes resealable bags for storage. Replicas include:
Braided polyester line has less stretch than nylon line and lasts longer than twisted line. It is woven in such a way that fraying occurs only on the surface without material loss of strength; when the braided jacket becomes fuzzy, you know it’s time for a replacement. Stretches 5% or less and can be calibrated with indelible marker.
These economical sieves are made of stainless steel mesh with steel frames. These sieves may be used for geological particle sizing. They are available as a set of 6 with a lid and a catch pan, or they may be purchased individually.
Sieves are available in the following mesh sizes: 5 (4000 micron), 10 (2000 micron), 35 (500 micron), 60 (250 micron), 120 (125 micron), and 230 (63 micron).
Sieve diameter is approximately 7 inches.
B36-60-06L Brushless Inrunner 4000kv
Max Current: 100A
Max Power: 1300W
Idle Current: 6.2A
Suggested ESC: 120A
Cell count: 2-3SLipo
Bolt holes spacing: 25mm
Bolt thread: M3.0*4
Gold Connection: Φ4.0
IUD Insertion Trainer Uterus, Product Details:
A compact hand-held IUD Insertion Trainer Uterus for demonstrating and perfecting IUD insertion technique. A variety of IUD's may be used. IUD not included.
IUD Insertion Trainer Uterus Features:
Made in USA by Gaumard Scientific.
One year limited warranty.
protein replicas with a kit that offers great savings. Kit is ideal for demonstrating portion sizes of different proteins. Resealable bags are included for storage. Replicas include:
• Kacang panggang • potongan daging sapi • dada ayam, digoreng • telur, digoreng • tenderloin • oleskan selai kacang • Ikan nila